Removal of Antimony and Bismuth from Copper Electrorefining Electrolyte: Part II—An Investigation of Two Proprietary Solvent Extraction Extractants

Antimony and bismuth recovery from copper electrorefining electrolyte could reduce the impacts of these problem elements and produce a new primary source for them. Two proprietary phosphonic acid ester extractants were examined (REX-1 and REX-2) for the removal of antimony and bismuth from copper electrorefining electrolytes. Experimentation included shakeout and break tests to determine the basic parameters for the extractants in terms of maximum loading, break times, and extraction and stripping efficiency. Five permutations of extractant mixtures (100 wt.% REX-1 and 25 wt.%, 50 wt.%, 75 wt.% and 100 wt.% REX-2) were studied. It was determined that REX-2 was able to extract Sb and Bi from the electrolyte, but required some mixture with REX-1 to better facilitate stripping with 400 g/L sulfuric acid. The laboratory electrorefining electrolyte containing glue had faster disengagement times than a synthetic solution without glue.     

Measurement of Young’s Modulus and Poisson’s Ratio of Thermal Barrier Coating Based on Bending of Three-Layered Plate

Thermal barrier coatings (TBCs) are used to protect the hot sections of gas turbine engines and airplane engines. A TBC system comprises a substrate, bond coat, and TBC topcoat. The development of an accurate method for determining the Young’s modulus and Poisson’s ratio of TBC using a multilayered specimen is of importance. In this study, we applied the bending theory of a laminated plate to a three-layered material and proposed models to determine the Young’s modulus and Poisson’s ratio of the TBC layer using the bending strain of the TBC system specimen. Three methods were developed by utilizing (i) the coating biaxial strain, (ii) substrate biaxial strain, or (iii) coating and substrate biaxial strains. Subsequently, we determined appropriate dimensions of the specimen and span by using three-dimensional finite element analysis, and numerically verified the usefulness of the three proposed methods. However, the Young’s modulus and Poisson’s ratio determined using the multilayered specimen with a substrate are sensitive to experimental errors. Therefore, we evaluated the sensitivity of the three proposed methods to experimental error, and we determined the most insensitive method among them. Finally, we experimentally demonstrated the usefulness of this method.     

Thermodynamic Properties of Superionic Phase Ag<Subscript>4</Subscript>HgSe<Subscript>2</Subscript>I<Subscript>2</Subscript> Determined by the EMF Method

Triangulation of the Ag-Hg-Se-I system in the vicinity of quaternary phase Ag₄HgSe₂I₂ was performed by differential thermal analysis, X-ray diffraction and electromotive force (EMF) methods. The spatial position of the phase region Ag₄HgSe₂I₂-Se-HgI₂ regarding the figurative point of silver was used to write the chemical reaction of formation of Ag₄HgSe₂I₂. The EMF measurements were carried out by applying an electrochemical cell: (–) C|Ag|Ag₂GeS₃ glass|Ag₄HgSe₂I₂, HgI₂, Se|C (+), where C is graphite and Ag₂GeS₃ glass is the fast purely Ag⁺ ions conducting electrolyte. The linear dependence of the EMF of the electrochemical cell on temperature was used to determine the standard thermodynamic values of Ag₄HgSe₂I₂ for the first time.     

First Principle and Experimental Study for Site Preferences of Formability Improved Alloying Elements in Mg Crystal

Some alloying elements (Al, Er, Gd, Li, Mn, Sn, Y, Zn) were proved recently by calculations or experiments to improve the formability of Mg alloys, but ignoring their site preference in Mg crystals during the calculated process. A crystallographic model was built via first principle calculations to predict the site preferences of these elements. Regularities between doping elements and site preferences were summarized. Meanwhile, in the basis of the crystallographic model, a series of formulas were deduced combining the diffraction law. It predicted that a crystal plane with abnormal XRD peak intensity of the Mg-based solid solutions, compared to that of the pure Mg, prefers to possess solute atoms. Thus, three single-phase solid solution alloys were then prepared through an original In-situ Solution Treatment, and their XRD patterns were compared. Finally, the experiment further described the site preferences of these solute atoms in Mg crystal, verifying the calculation results.     

Effects of Solution Treatment Temperatures on Microstructure and Mechanical Properties of TIG–MIG Hybrid Arc Additive Manufactured 5356 Aluminum Alloy

A novel additive manufacturing method with TIG–MIG hybrid heat source was applied for fabricating 5356 aluminum alloy component. In this paper the microstructure evolution, mechanical properties and fracture morphologies of both as-deposited and heat-treated component were investigated, and how these were affected by different heat-treated temperature. The as-deposited microstructure showed dominant equiaxed grains with second phase, and the size of them is coarse in the bottom region, medium in the middle region and fine in the top region owing to different thermal cycling conditions. Compared with as-deposited microstructure, the size of grain becomes large and second phases gradually dissolve in the matrix as heat-treated temperature increase. Different microstructures determine the mechanical properties of component. Results show that average ultimate tensile strength enhances from 226 to 270 MPa and average microhardness increases from 64.2 to 75.3 HV0.1 but ductility decreases from 33 to 6.5% with heat-treated temperature increasing. For all components, the tensile properties are almost the same in the vertical direction (Z) and horizontal direction (Y) due to equiaxed grains, which exhibits isotropy, and the mechanisms of these are analyzed in detailed. In general, the results demonstrate that hybrid arc heat source has the potential to fabricate aluminum alloy component.     

Energy Detection in Hoyt/Gamma Fading Channel with Micro-Diversity Reception

Spectrum sensing is the important function of cognitive radio and energy detection is the most popular technique used for spectrum sensing. Detection of the availability of unused spectrum for the secondary user becomes difficult when the channel is affected by composite multipath/shadowed fading. In this paper, the performance analysis of an Energy Detector in Hoyt/gamma composite fading channel with Maximum Ratio Combining employing micro-diversity is analyzed. Analytical expressions for performance parameters, i.e., the average probability of detection and the average area under the receiver operating characteristics curve are evaluate. The effect of diversity on the performance of energy detector is also studied. Monte-Carlo simulation results have verified the accuracy of the proposed analysis.     

Decision Support for the Comparative Evaluation and Selection of Analytical Methods: Detection of Genetically Modified Organisms as an Example

The selection of the best-fit-for-purpose analytical method to be implemented in the laboratory is difficult due to availability of multiple methods, targets, aims of detection, and different kinds and sources of more or less reliable information. Several factors, such as method performance, practicability, cost of setup, and running costs need to be considered together with personnel training when selecting the most appropriate method. The aim of our work was to prepare a flexible multicriteria decision analysis model suitable for evaluation and comparison of analytical methods used for the purpose of detecting and/or quantifying genetically modified organisms, and to use this model to evaluate a variety of changing analytical methods. Our study included selection of PCR-, isothermal-, protein-, microarray-, and next-generation sequencing-based methods in simplex and/or multiplex formats. We show that the overall result of their fitness for purpose is relatively similar; however, individual criteria or a group of related criteria exposed more substantial differences between the methods. The proposed model of this decision support system enables easy modifications and is thus suitable for any other application of complex analytical methods.     

Synthesis of N-doped mesoporous carbons under different carbonization temperature and their application in supercapacitors

We have synthesized N-doped mesoporous carbon by the in-suit doping template method under the carbonized temperature of 900?°C. We found that the electrochemical performance of mesoporous carbon was enhanced by N-doping. So, we tried to increase the content of nitrogen to further optimize the electrochemical performance of the mesoporous carbon as electrode materials. During the process of synthesizing mesoporous carbon, the carbonized temperature played an important role in the formation of the carbon structure and its morphology, as well as in determining the content of nitrogen. We attained a considerable electrochemical performance enhancement by changing the carbonized temperature from 900 to 700?°C. We found the content of Nitrogen decreased with the increase of the carbonized temperature and the content of Nitrogen is 6.11% at 700?°C, 5.39% at 800?°C, 3.9% at 900?°C, respectively. The best electrochemical performance was observed in the product carbonized at 700?°C, which exhibited high specific capacitance (245.6 F/g at 0.5 A/g) and good cycle ability (more than 90% of the initial capacitance after 5000 cycles) in 6 M KOH electrolyte.